ridm@nrct.go.th   ระบบคลังข้อมูลงานวิจัยไทย   รายการโปรดที่คุณเลือกไว้

Clegg, Richard E.
หน่วยงาน Central Queensland University, Australia
จำนวนงานวิจัยจำแนกรายปี
บุคคลที่เคยร่วมงานวิจัย
ความเชี่ยวชาญ
ปี
# พ.ศ. จำนวน
1 2556 3
2 2555 5
3 2554 9
4 2553 7
5 2552 3
6 2551 4
7 2550 1
8 2549 3
9 2548 1
10 2547 2
11 543 2
ผลงานวิจัย
# หัวเรื่อง
ปี พ.ศ. 2556
1 TEM Characterizations of Iron Oxides of Mild Steel Formed at High-Temperature and High-Concentration NaOH
2 Effect of exposure time on the morphology of corrosion on high chromium white cast iron in high temperature caustic solutions
3 Behaviour of Grade 310H Stainless Steel Exposed to High Temperature Hydrocarbon Processing Gases
ปี พ.ศ. 2555
4 The theory of critical distances and fatigue from notches in aluminium 6061
5 Corrosion resistance of white cast irons in caustic solutions
6 Study on carbide cutting tool life using various cutting speeds for α-β Ti-alloy machining
7 Influence of temperature on the structure of oxide films formed on mild steel exposed to hot caustic
8 Study on carbide cutting tool life using various cutting speeds for α-β Ti-alloy machining
ปี พ.ศ. 2554
9 Residual stress analysis on machined surface in turning Stellite 6
10 Effects of replication on measured S-N curves of metals
11 Experimental study on theory of critical distance applied to the prediction of fatigue from notches
12 Ammonium nitrate induced cracking of a dryer
13 Experimental setup and methodology for the analysis of rail lubricant effectiveness
14 Corrosion behaviour of high chromium white irons in high temperature caustic
15 Mercury embrittlement crack initiation in 5083 aluminum alloys : the role of the oxide film
16 Editorial : the Fourth International Conference on Engineering Failure Analysis
17 A method of quantifying dilute volatile organic compounds in air
ปี พ.ศ. 2553
18 Optimisation of the machining of Stellite 6 PTA hardfacing using surface roughness
19 Attrition assessment of alumina using single impact with variable air stream velocity
20 Measurements of the interface between 5083 aluminium and liquid mercury using impedance spectroscopy
21 Use of impedance spectroscopy to study the integrity of the aluminium oxide films in mercury embrittled aluminium
22 Editorial : [Engineering failure analysis]
23 Attrition index a measure for environmental pollution caused by alumina /
24 Effect of cutting tool nose radius on surface roughness for Stellite 6 machining using coated carbide insert
ปี พ.ศ. 2552
25 Continuous and discontinuous crack growth in brass embrittled by liquid gallium
26 A rational between manufacturing processes design and manufacturing cost
27 Do all welds have cracks?
ปี พ.ศ. 2551
28 Methodology for measurement of lubricant decay rate for rail lubricants
29 Development of a new attrition index using single impact
30 Use of the master curve to investigate the effect of post-weld heat
31 Filshie clip closure : determination of closure through the analysis of x-rays
ปี พ.ศ. 2550
32 Investigation of the use of near infrared FBG (830nm) sensors for monitoring the structural response of 0/90 woven cloth/CSM glass fibre/vynylester composite under static and fatigue loading
ปี พ.ศ. 2549
33 An experimental investigation of the properties of cross-ply laminate used for manufacturing of small aircraft components
34 Modifications of a rail / wheel simulator to measure rail curve lubricant performance
35 Electrochemical characterisation of the parallel disk device
ปี พ.ศ. 2548
36 A rotating parallel disc device for corrosion studies
ปี พ.ศ. 2547
37 University/industry collaboration : achieving the best possible outcomes
38 Ductile particle toughening of hydroxyapatite ceramics using platinum particles
ปี พ.ศ. ไม่ระบุ
39 Final report on effect of oxide film integrity on mercury embrittlement of aluminium
40 Evaluation of caustic cracking in welded samples - three tests final report /